Huawei FusionCol8000-E240 User Manual Download Page 80

Page: 80 / 305

Table 4-5 Cable terminal requirements

Port

Connection

Method

Bolt

Specificatio

Torque

Remarks

Active input

Crimped DT

terminals

M10

20 N·m

Standard

configuratio

n, delivered

with the

product.

Standby

input

Crimped DT

terminals

M10

20 N·m

Standard

configuratio

n, delivered

with the

product.

4.3 Installing a FusionCol8000-E

4.3.1 Unpacking and Checking

Procedure

Step 1 Verify that the package is intact. If any damage is found, notify the carrier

immediately.

Step 2 Remove the plastic packaging materials.
Step 3 Check the types and quantity of fittings according to the fitting list. If any fitting is

missing, contact Huawei technical support.

----End

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (FDC Scenario)

Issue 02 (2021-04-15)

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands