Huawei FusionCol8000-E240 User Manual Download Page 60

Page: 60 / 305

Figure 3-21 Ports for a water sensor (rope-type)

----End

3.4.4 (Optional) Installing Teamwork and Monitoring

Communications Cables

NO TICE

● Smart cooling products of different models and software versions cannot be

networked for teamwork.

● Connect teamwork and monitoring communications cables based on the

networking scenario.

● The teamwork communications cable must be a shielded network cable of Cat

5e or higher specifications. The network cable length between adjacent devices

must be less than or equal to 100 m, and the distance for CAN teamwork

communication must be less than or equal to 310 m.

● Route cables in compliance with local standards. Take appropriate shielding

measures, such as using a galvanized pipe or an ELV cable tray, to reduce the

impact of electromagnetic interference on teamwork communication.

Otherwise, teamwork networking may fail.

3.4.4.1 Preparing a Network Cable

Step 1 Crimp a network cable.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

3 System Installation (Building Scenario)

Issue 02 (2021-04-15)

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands