Huawei FusionCol8000-E240 User Manual Download Page 58

Page: 58 / 305

●

Cables should be securely connected and free of contact with components,

such as the fan.

●

When laying out cables, ensure that the power cables and signal cables are

reliably separated and that electric and extra low voltage (ELV) cables are

bound separately.

●

Cable colors in this document are for reference only.

3.4.2 Cable Routes

Figure 3-19 Cable routes

(1) Power cable

(2) Exhaust air damper cable

(3) Supply air damper cable

(4) Electric heater controller

cable

(5) Signal cable

3.4.3 (Optional) Installing Signal Cables

Prerequisites

Signal cables must be routed through protective tubes for protection.

The device can be connected to a smoke sensor, remote startup/shutdown signal,

public alarm signal, and water sensor. The following describes how to connect a

water sensor.

Context

Figure 3-20 Signal cable terminal (using X501 as an example)

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

3 System Installation (Building Scenario)

Issue 02 (2021-04-15)

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands