Huawei FusionCol8000-E24 User Manual Download Page 91

Page: 91 / 269

Figure 5-15 Removing sheet metal fasteners from a compressor

NO TE

● Do not remove the bolts.
● Keep the removed sheet metal fasteners properly for future transportation.

Step 6 Tighten the bolts on the compressors again to a torque of 12 N·m.

Step 7 Install the maintenance door for the compressors.

----End

5.5 Installing Cables

5.5.1 Precautions

●

Connections of all power cables, control cables, and ground cables must

comply with local electrical regulations, and the cable specifications should

comply with local cabling specifications.

●

For details about the maximum current, see the nameplate of the unit.

●

Check that the input voltage and frequency of the primary power supply meet

the requirements.

●

Only trained and qualified personnel are allowed to connect cables.

●

Before connecting cables, use a multimeter to measure the input voltage and

ensure that the power supply is disconnected.

●

All units must be reliably grounded before power-on.

●

Cables should be securely connected and free of contact with components,

such as the fan.

●

When laying out cables, ensure that the power cables and signal cables are

reliably separated and that electric and extra low voltage (ELV) cables are

bound separately.

●

Cable colors in this document are for reference only.

5.5.2 (Optional) Installing Signal Cables

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands