Huawei FusionCol8000-E24 User Manual Download Page 78

Page: 78 / 269

●

Do not expose the unit to strong sunlight in summer. Otherwise, the thermal

insulation panels may be deformed.

●

Do not stack whole units together.

5.2 Tools

The onsite technical personnel can select tools based on the site requirements.

Category

Tool

Personal

protective

equipment (PPE)

Safety gloves

Safety goggles

Dust mask

Safety shoes

Safety helmet

Safety belt

Transportation

Manual pallet

truck

Electric pallet

truck

Installation

Crane (> 50,000

kg)

Lifting rope

Hoisting rope

Jack

Level gauge

Level

Vacuum cleaner

Ink fountain

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

5 System Installation (FDC Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands