Huawei FusionCol8000-E24 User Manual Download Page 54

Page: 54 / 269

No.

Item

Check Method

Expected Result

Bolts and nuts

Partially tighten them

using a wrench.

Bolts and nuts are

tightened.

Maintenance door

Open and close the

maintenance doors.

All maintenance doors

can be smoothly

opened and closed.

4.4.3 Checking the Refrigerant

Procedure

Step 1 Open the maintenance door to the compressors.

Step 2 Check whether any needle valve bonnet of the compressors is missing.

1. If any bonnet is missing, contact Huawei technical support.
2. If no bonnet is missing, remove the valve bonnets, and press the valve plugs

using the valve bonnets in turn. If gas flows out, the system is normal. If no

gas flows out, contact Huawei technical support.

Figure 4-8 Needle valve positions

(1) Low-pressure needle valve

(2) Liquid pipe needle valve

----End

4.4.4 Installing Air Ducts

Prerequisites

Before the installation, ensure that there is no construction waste in the air shaft.

Context

●

Air ducts need to be prepared by the customer based on the site

requirements. The air duct in the figure is for reference only.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands