Huawei FusionCol8000-E24 User Manual Download Page 150

Page: 150 / 269

Item

Expected Result

Troubleshooting

Screws on the indoor fan and

exhaust fan are not loose or

distorted.

Tighten the screws using a 10#

socket wrench.

Water

pump

The water pump is not

rusted.

Remove the rust.

No water leaks from the

water pump spindle seal.

If water leaks, replace the water

pump or water pump spindle seal.

Water

sampling

During the first half year of

operation, take a sample

from each route of supplied

water and from circulating

water for one of units for

each computer room every

month.

NOTICE

Spray water can be circulated

for six times by default, which

can be changed depending on

the local climate and water

source conditions.

If the test result does not the

water quality requirements,

perform a test again and increase

the test frequency (it is

recommended that sampling be

conducted half a month). If the

results of three consecutive tests

do not the requirements, find out

the cause in water supply and take

corresponding measures to ensure

normal operation of the spray

system.

9.2.2 Quarterly Maintenance

Table 9-2 Quarterly maintenance checklist

Comp

onent

Item (on the Basis of Monthly

Maintenance)

Troubleshooting

Monito

ring

system

Export logs, alarms, temperature,

humidity, and the operating status

and time of the compressor, fan,

spray system, and spray pump

from the monitoring system. View

historical alarms generated in this

quarter and select the most

common five ones. (If no

monitoring system is available, skip

this item.)

NOTE

If the value of Spray pump running

status is 0%, the spray pump is

stopped. Otherwise, the pump is

running.

Locate the cause or contact

technical support.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

9 System Maintenance

141

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands