Huawei FusionCol8000-E24 User Manual Download Page 134

Page: 134 / 269

Parameter

Description

Link mode

● Server: The smart cooling product works as the

server and can connect to two clients for

communication.

● Client: The smart cooling product works as the

client and can connect to a remote server for

communication.

● Server and client: The smart cooling product works

as the server and can connect to two clients for

communication. It also works as the client and can

connect to a remote server for communication.

Client encryption

This parameter is configurable when Link mode

involves Client.

Server encryption

This parameter is configurable when Link mode

involves Server.

Encryption algorithm

CBC

Specifies whether to use the CBC encryption algorithm.

After the parameter setting is changed, the system

automatically restarts. Exercise caution with the setting.

NMS IP address

Enter the actual IP address of the NMS. The IP

addresses of the display board, client NMS, and server

NMS must be unique.
This parameter is configurable when Link mode

involves Client.

NMS port number

This parameter is configurable when Link mode

involves Client.
● Connecting to the NetEco: Set this parameter to

32907 if Client encryption is enabled, or set it to

32906 if Client encryption is disabled.

● Connecting to other NMSs: You are advised not to

change the value. In special cases, set this

parameter based on the site requirements.

Pre-shared password

Secondary authentication password used for Modbus-

TCP connection.

----End

7.4.4.3 Setting Communications Parameters (SNMP Protocol)

Context

●

To set communications parameters, log in as the admin user.

●

This section is suitable only for SNMP. Skip this section if you use Modbus.

●

Record the values entered in this section. They will be used when you connect

a unit to a network management system (NMS).

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

125

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands