Huawei FusionCol8000-E24 User Manual Download Page 125

Page: 125 / 269

7.4.2 (Optional) Setting the Pressure Difference Control

Prerequisites

If the differential pressure sensors are installed, perform the following operations

accordingly. If the differential pressure sensors are not installed, skip this section.

Procedure

Step 1 On the home screen, choose Settings > System Settings > Indoor fan, set Air-

side differential pressure sensor type to 0~125 Pa comm port.

Step 2 Set Indoor fan control type to Pressure diff ctrl.
Step 3 Change the other parameters based on the following instructions.

Parameter

Description

Indoor fan control

type

● Return/supply air temperature difference proportion

control: controls the indoor fan speed based on the

proportion of temperature difference between

return air and supply air.

● Return/supply air temperature difference control:

controls the indoor fan speed based on the

temperature difference between return air and

supply air.

● Pressure difference control: controls the indoor fan

speed based on the pressure difference.

Indoor fan pressure

difference setpoint

Specifies the control value of indoor fan pressure

difference.

Air-side differential

pressure sensor type

Select the proper differential pressure sensor type

based on the measurement range of the differential

pressure sensor.

Min indoor fan speed

Specifies the minimum rotational speed of the indoor

fan.

Max indoor fan speed

Specifies the maximum rotational speed of the indoor

fan.

----End

7.4.3 (Optional) Setting Teamwork Parameters

Prerequisites

The teamwork group number and addresses for the units have been set as follows:
●

Teamwork group No.: Group the units in same aisle or adjacent areas as one,

that is, assign one teamwork group number for them. At most four teamwork

groups can be assigned (1–4).

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

116

Summary of Contents for FusionCol8000-E24














































































































































































































































































Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands

Huawei FusionCol8000-E24, User Manual

Search results

Summary of Contents for FusionCol8000-E24

Reviews:

Related manuals for FusionCol8000-E24

Brands by name

Popular brands