manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

7

 Power-On Commissioning

7.1 Preparing for Power-On

Procedure

Step 1 Verify that the switch for the unit in the upstream power distribution frame (PDF)

is OFF.

Step 2 Verify that the input voltage meets the requirement.

D ANGER

Ensure that there is no reverse or open phase for the input power cable of the

unit. Otherwise, the unit may be damaged beyond repair.

Step 3 Verify that cables are correctly connected and the phase sequence is correct.

Step 4 If teamwork networking is required, verify that the teamwork cable is correctly

connected.

Step 5 If the cabinet is connected to the temperature and humidity sensor, check that the

cable connection and DIP switch settings are correct.

----End

7.2 Powering On the Unit

Step 1 Turn on the main switch of the unit. (For a unit with dual power supplies, turn on

both the active and standby power switches.)

Step 2 Turn on the upstream power input switch of the unit. The display module turns on

automatically.

Step 3 After the initial power-on, the Quick Settings screen is displayed. Log in as user

admin.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

7 Power-On Commissioning

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

101

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Daikin SUPER MULTI NX FDXS09LVJU Operation Manual preview
SUPER MULTI NX FDXS09LVJU
Brand: Daikin Pages: 30
Dawlance Chrome Owner'S Manual preview
Chrome
Brand: Dawlance Pages: 8
Haier IKI-09 User Manual preview
IKI-09
Brand: Haier Pages: 28
Haier HSM-24HEA03-R2 Manual preview
HSM-24HEA03-R2
Brand: Haier Pages: 8
Haier HSU-040C01 User Manual preview
HSU-040C01
Brand: Haier Pages: 25
Haier HPU-42CV03 Operation And Installation Manual preview
HPU-42CV03
Brand: Haier Pages: 30
Haier AS26TB1HRA Operation Manual preview
AS26TB1HRA
Brand: Haier Pages: 8
Haier AS072XCBAA Manual De Operación preview
AS072XCBAA
Brand: Haier Pages: 16
Haier AMA05JF Manuel preview
AMA05JF
Brand: Haier Pages: 17
Haier HSU-18HEA03(T3) Installation Manual preview
HSU-18HEA03(T3)
Brand: Haier Pages: 8
Haier HSU-09H03/R Operation Manual preview
HSU-09H03/R
Brand: Haier Pages: 27
Haier HSU-09H03/K(F) Installation Manual preview
HSU-09H03/K(F)
Brand: Haier Pages: 4
Haier HSU-09RR03-R2 Kayttoohje preview
HSU-09RR03-R2
Brand: Haier Pages: 18
Haier QPCA09 Owner'S Manual And Installation Instructions preview
QPCA09
Brand: Haier Pages: 16
Haier HSU-09HVD03/R2 - annexe 2 Manual preview
HSU-09HVD03/R2 - annexe 2
Brand: Haier Pages: 14
Haier HSU-09HEA13/R2 Installation Manual preview
HSU-09HEA13/R2
Brand: Haier Pages: 8
Haier HSU-18CVY03 Installation Manual preview
HSU-18CVY03
Brand: Haier Pages: 8
Vax ONEPWR Spotless Go CLCW-MSKS User Manual preview
ONEPWR Spotless Go CLCW-MSKS
Brand: Vax Pages: 12

Brands by name

Popular brands

Load more brands