Huawei eSpace IPC 2601-P User Manual Download Page 14

Page: 14 / 84

eSpace IPC 2601(5601)-P
User Guide

Hardware Installation

Issue 01 (2012-10-15)

Huawei Proprietary and Confidential

Removing a Lens

This topic describes how to remove a lens.

Step 1

Shut down and power off the IPC.

Step 2

(Optional) Remove the lens cable from the auto aperture connector. Skip this step when
a manual aperture lens is used.

Step 3

(Optional) Remove the Zoom/Focus lens cable from the Zoom/Focus lens interface.
Skip this step when prime lens or manual zoom lens cameras are used.

Step 4

Unscrew the lens in a counter-clockwise direction.

Step 5

Install a CMOS protective cover.

----End

3.2 Connecting External Devices to an IPC

This topic introduces the method for connecting IPC interfaces to external devices.

Figure 3-4 shows the connection between IPC interfaces and external devices. For
details about the interface position, see Table 2-2.

Summary of Contents for eSpace IPC 2601-P





















































































Search results

Summary of Contents for eSpace IPC 2601-P

Reviews:

Related manuals for eSpace IPC 2601-P

Brands by name

Popular brands

Huawei eSpace IPC 2601-P, User Manual

Search results

Summary of Contents for eSpace IPC 2601-P

Reviews:

Related manuals for eSpace IPC 2601-P

Brands by name

Popular brands