Huawei EDFA0820-D Routine Maintenance Manual Download Page 20 | Manualshive

Page: 20 / 46

background image

Attribute

Alarm ID

Alarm Severity

Alarm Type

65539

Major

Fault alarm

Parameter

Parameter

Description

Frame

Subrack number of the EDFA

Slot

Slot number of the EDFA

PUMP

PUMP ID. Value: 1

the pump current

Actual current of EDFA PUMP1

Impact on the System

The EDFA service life is affected.

Possible Cause

The current in PUMP1 exceeds the current alarm threshold.

Handling Procedure

Check whether the current alarm threshold is set to a proper value. If it is set to a proper
value, contact Huawei.

Alarm Clearing Condition

When the current of EDFA PUMP1 drops below the preset alarm threshold, the alarm is
cleared.

2.3.3.2 ALM-65540 EDFA PUMP1 Temperature Alarm

Description

The temperature of PUMP1 exceeds the upper threshold.

The temperature of PUMP1 is below the lower threshold.

Alarms are generated for both scenarios.

EDFA0820-D
Routine Maintenance Guide

2 Common Alarm Handling

Issue 02 (2018-07-02)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

14

«
...
18
19
20
21
22
...
»

Summary of Contents for EDFA0820-D















































Reviews:

No comments

Related manuals for EDFA0820-D

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Salda Pages: 16

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 7

Brand: National Instruments Pages: 22

Brand: SYCLOPE electronic Pages: 40

Brand: Timotion Pages: 10

Brand: Gecko Pages: 82

Brand: XP Metal Detectors Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands