Huawei ECC800-Pro User Manual Download Page 84

Page: 84 / 368

Item

Specifications

Storage temperature

–40°C to +70°C

Output

RS485

3.2.19.3 T/H Sensor (BOM Number: 33010516)

Figure 3-40 Appearance

The T/H sensor uses an RJ45 connector.

NO TE

The appearance of the T/H sensor depends on the onsite delivery.

Figure 3-41 Pins of an RJ45 connector

Table 3-68 RJ45 port pin definitions

Pin

Description

Pin1 or Pin 4

Pin2 or Pin 5

Pin3

V+

Pin6

V-

Pin7

Reserved

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands