Huawei ECC800-Pro User Manual Download Page 76

Page: 76 / 368

Figure 3-32 Electrode water sensor

Table 3-58 Technical specifications of the electrode water sensor

Item

Specification

Operating

temperature

–40°C to +80°C

Storage

temperature

–40°C to +80°C

Service life

10 years

3.2.16 WiFi Module

The WiFi module provides WiFi signals for equipment such as pads and mobile

phones to interact with the host computer.

Figure 3-33 WiFi module

Table 3-59 Technical specifications

Item

Specifications

Wireless

standard

IEEE 802.11n, IEEE 802.11g, and IEEE 802.11b

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands