Huawei ECC800-Pro User Manual Download Page 67

Page: 67 / 368

Figure 3-24 Smoke sensor

Table 3-48 Technical specifications of a smoke sensor

Item

Specifications

Operating voltage

DC12 V (9–16 V DC)

Quiescent current

< 8 mA

Alarm current

< 35 mA

Output mode

Relay output

Output contact capacity

3 A/120 V AC or 3 A/24 V AC

Operating temperature

–10ºC to +50ºC

Ambient humidity

< 95% RH (non-condensing)

Dimensions

Diameter: 112 mm, height: 41 mm

3.2.10 Temperature Sensor

The temperature sensor (BOM number: 33010348) is used for the surface

temperature measure, industrial process control, measurement instrument, etc.

Figure 3-25 Temperature sensor

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

3 Device Description

Issue 02 (2020-09-07)

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands