Huawei ECC800-Pro User Manual Download Page 124

Page: 124 / 368

Follow-up Procedure

To modify or delete the email parameter settings, click Modify or Delete.

5.5 Commissioning the New Main Way

Context

●

In the new main way scenario, general input units and power distribution

units communicate with the ECC800-Pro using the Modbus-MAC protocol.

After the general input units and power distribution units properly connect to

the ECC800-Pro, the ECC800-Pro automatically identifies the units.

●

Then, you need to set parameters for the general input units and power

distribution units; otherwise, a false alarm may be generated.

Procedure

Step 1 Set parameters for general input units on the ECC800-Pro WebUI.

1. Set parameters for general input unit 1.

Table 5-3 Power distribution settings for a general input unit

Path

Parameter

Name

Defaul

Value

Setting

Monitoring > Power

Distribution > General

Input Unit > Running

Parameters > Power

Distribution Settings

Rated system

frequency

Set based on actual

conditions.

Rated system

voltage

380

Set based on actual

conditions.

Rated system

current

NOTE

This

parameter is

not displayed

for some

general input

units.

250

Set based on actual

conditions.

NOTE

Set this parameter to a

value consistent with the

information on the

nameplate of the general

input unit. For example, if

the model is NMW-0250

AC, set Rated system

current to 250 A.

System CT

ratio

NOTE

This

parameter is

not displayed

for some

general input

units.

250

Set based on actual

conditions.
For example, if Rated

system current is 250

A, set System CT ratio

to 250.

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

5 Power-On Commissioning

Issue 02 (2020-09-07)

113

Summary of Contents for ECC800-Pro

















































































































































































































































































































































































Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands

Huawei ECC800-Pro, User Manual

Search results

Summary of Contents for ECC800-Pro

Reviews:

Related manuals for ECC800-Pro

Brands by name

Popular brands