manualshive.com logo in svg

Huawei DBS3900 IBS, Hardware Description, Page: 27 / 28

Share
Download
Huawei DBS3900 IBS Hardware Description Download Page 27

 
DRH3980A&3909A&3918A& 
3918B&3921A&3921B&3926A 
Hardware Description   

5 Appendix 

 

Issue DraftA (2013-08-10) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd.. 

21 

 

 

 

For DRH3926A, please keep 2.01m or more. 

WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC 
LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or 
express consent of an FCC Licensee to operate this device. Unauthorized use may result in 
significant forfeiture penalties, including penalties in excess of $100,000 for each continuing 
violation. 

 

The manufacturer is not responsible for any radio or TV interference caused by unauthorized 

modifications to this equipment. Such modifications could void the user authority to operate 

the equipment. 

. 

5.2 

Canada Regulatory Compliance 

5.2.1 RSS-Gen statement 

This device complies with Industry Canada licence-exempt RSS standard(s). 

Operation is subject to the following two conditions: (1) this device may not cause 
interference, and (2) this device must accept any interference, including interference that may 
cause undesired operation of the device. 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio 
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil 
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le 
fonctionnement. 

5.2.2 RSS-102 statement: 

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 
and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF 
exposure and compliance.   

Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de 
RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information 
canadienne sur l'exposition et la conformité de rf. 

This equipment complies with IC radiation exposure limits set forth for an uncontrolled   

environment. This transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter. The minimum installed and operated distance between the   

radiator and your body of each model as below. 

For DRH3926A, please keep 2.01m or more. 

Cet équipement est conforme à l'exposition aux rayonnements IC limites établies pour 
unenvironnement non contrôlé. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en 

Summary of Contents for DBS3900 IBS





























Reviews:

No comments