Huawei CX320 User Manual Download Page 104

Page: 104 / 113

Figure 6-10

WinSCP login

Step 3

Set the login parameters.

The parameter descriptions are displayed as follows:

Host name: Specifies the IP address of the device to be connected. For example:

191.100.34.32

Port number: The default value is

User name: Specifies the username. For example: admin123

Password: Specifies the password. For example: admin123

Private key file: Retain the default value

None

Protocol: Select the default value

SFTP

, and then select

Allow SCP fallback

Step 4

Click

Login

The

WinSCP

file transfer page is displayed.

NOTE

If a key file was not selected during the first login, a warning

Continue connecting and add host

key to cache

is displayed. Click

Yes

. The

WinSCP

file transfer page is displayed.

If Windows 7 is used, in the left pane of the page, open the

C:\Users\Administrator\Documents

directory, the device's

/root

directory is opened in the right pane by default.

Step 5

In the left and right panes, create or delete folders, or copy folders between the left and right
panes.

----End

CX320 Switch Module
User Guide

6 Common Operations

Issue 09 (2019-08-02)

Summary of Contents for CX320


















































































































Search results

Summary of Contents for CX320

Reviews:

Brands by name

Popular brands

Huawei CX320, User Manual

Search results

Summary of Contents for CX320

Reviews:

Brands by name

Popular brands