manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 90 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 90

Table 5-3

 Continuous presence specifications

Terminal
Model

Video Protocols and Resolutions

Maximum Number
of Panes

ViewPoint 9039

H.264 720p

6

Any combination of H.264 720p and H.264
4CIF/4SIF, H.264 CIF/SIF, H.263 CIF/SIF,
and H.261 CIF/SIF

6

H.264 4CIF/4SIF, H.264 CIF/SIF, H.263 CIF/
SIF, H.261 CIF/SIF, or any combination of the
preceding

9

ViewPoint 9036

H.264 720p

4

Any combination of H.264 720p and H.264
4CIF/4SIF, H.264 CIF/SIF, H.263 CIF/SIF,
and H.261 CIF/SIF

4

H.264 4CIF/4SIF

6

Any combination of H.264 4CIF/4SIF and H.
264 CIF/SIF, H.263 CIF/SIF, or H.261 CIF/SIF

4

H.264 CIF/SIF, H.263 CIF/SIF, H.261 CIF/
SIF, or a combination of any two of the
preceding

6

HUAWEI
VP9039A
ViewPoint 9039S

H.264 720p 50 Hz/60 Hz, H.264 720p 30 Hz/
25 Hz, H.264 4CIF/4SIF, H.264 CIF/SIF, or
any combination of the preceding

NOTE

Including the local site whose built-in MCU is being
used, a maximum of three H.264 sites whose video
resolution is 720p 50 Hz or 720p 60 Hz can
participate in one conference simultaneously.

6

HUAWEI
VP9036S

H.264 720p 50 Hz/60 Hz, H.264 720p 30 Hz/
25 Hz, H.264 4CIF/4SIF, H.264 CIF/SIF, or
any combination of the preceding

4

ViewPoint 9030
HUAWEI
VP9035A

H.264 720p 30Hz/25Hz

、

H.264 4CIF/4SIF

、

H.264 CIF/SIF, or any combination of the
preceding

6

 

Automatic Continuous Presence

Based on the continuous presence and adaptation capabilities of the built-in MCU and the
number of the sites called to join a conference, the terminal automatically generates the
continuous presence. There are four continuous presence modes in an automatic continuous
presence conference, namely, 4 panes, 6 panes, 8 panes, and 9 panes, as described in 

Table

5-4

.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

78

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments