manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 143 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 143

Parameter

Description

Background
color

This specifies the background color of the caption. The system supports
a maximum of 64 colors.

Font color

This specifies the font color of the caption in the foreground. The system
supports a maximum of 64 colors.

Font size

This specifies the font size of the caption. The available options are tiny,
less, small, medium, large, biggish, and huge.

Bold

This specifies whether the font of the caption is in bold.

Scrolling
speed

The middle and bottom captions can roll in display. This parameter is
used to specify the rolling rate of a caption. Seven rolling rates are
available for a middle caption and five for a bottom caption. The
required rate can be chosen according to the preview effect.

 

----End

Follow-up Procedure

After a caption or a banner is created, you can preview, send, or edit the caption or the banner.

8.3 Sharing a Caption

After you create a caption, you can share the caption with a remote site.

Prerequisites

A caption has been created.

Procedure

Step 1

From the home screen, select 

Utilities

.

Step 2

Select 

Middle Caption

, 

Banner

, or 

Caption

 according to different software versions.

Step 3

Select a caption or a banner, and then select 

Share

.

----End

8.4 Sending an Instant Message

During a conference, instant messages can be sent to remote sites.

Prerequisites

Both the sending party and the receiving party support T.140 captions. For details about how to
configure T.140 captions, see section 

8.1 Configuring Captions

.

HUAWEI 9000 HD Video Terminal
Administrator Guide

8 Captions

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

131

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments