manualshive.com logo in svg

Huawei 3900 Series, Commissioning Manual

Introducing the Huawei 3900 Series - a cutting-edge solution for all your technological needs. This exceptional product offers unparalleled performance and functionality. Enhance your experience with our easy-to-use Solution Manual, available for free download at manualshive.com. Discover the limitless possibilities of the Huawei 3900 Series today!

Share
Download
background image

6

 Commissioning the MBTS by Using USB

and M2000

About This Chapter

This chapter describes how to upgrade software and configure data using a USB disk, check the
operating status of the MBTS hardware, and rectify the MBTS hardware faults (if any) in time
at the MBTS. This section also describes how to check the operating status of the MBTS on the
M2000.

6.1 Procedure for Commissioning the MBTS by Using USB and M2000

At the local end of the MBTS, you can use a USB disk to upgrade the MBTS software and data,
and check whether the MBTS hardware status is normal according to the board status and LED
status, to locate and rectify faults in time. At the remote end of the MBTS, you can perform fault
diagnosis on the MBTS and verify services of the MBTS on the M2000.

6.2 Preparing the USB Disk for Local Commissioning

The USB disk should be ready before it is used for local commissioning. The preparation of the
USB disk for local commissioning varies according to the base station mode. Therefore, you
must prepare the USB disk based on the mode of the base station to be commissioned.

6.3 Upgrading Software and Configuring Data by Using the USB Disk

You can locally upgrade software and configure data of a base station by using the USB disk on
the base station side.

6.4 Checking the Status of the LEDs and Rectifying the Faults

This section describes how to check the operating status of the LEDs according to the states of
the LEDs on the modules of the base station.

6.5 Set the Download Control Right

If the BTS is working in the co-module scenario, the download control right needs to be set. The
system with the download control right upgrades the co-modulated RRU3908/MRFU and the
USCU software during software upgrade.

3900 Series Multi-Mode Base Station
Commissioning Guide

6 Commissioning the MBTS by Using USB and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

6-1

Summary of Contents for 3900 Series





































































































































































































Reviews:

No comments

Related manuals for 3900 Series

KARPO Fly NEON Operating Instruction preview
NEON
Brand: KARPO Fly Pages: 13
JETBAG 320 Fitting Instructions Manual preview
320
Brand: JETBAG Pages: 44
QC Conveyors INDUSTRIAL Series Installation & Maintenance Instructions Manual preview
INDUSTRIAL Series
Brand: QC Conveyors Pages: 44
Lanaform Heating Overblanket Instructions For Use Manual preview
Heating Overblanket
Brand: Lanaform Pages: 84
Lanaform Aroma Globe Instruction Manual preview
Aroma Globe
Brand: Lanaform Pages: 84
Lanaform Aroma Design Manual preview
Aroma Design
Brand: Lanaform Pages: 72
Lanaform Aroma Decor Instruction Manual preview
Aroma Decor
Brand: Lanaform Pages: 80
Magellan CYCLO 315 Series User Manual preview
CYCLO 315 Series
Brand: Magellan Pages: 39
MadStad Engineering MadStad Installation Instruction preview
MadStad
Brand: MadStad Engineering Pages: 2
U-Line H-5598 Manual preview
H-5598
Brand: U-Line Pages: 3
Xerox 7400DN - Phaser Color LED Printer Accessories Manual preview
7400DN - Phaser Color LED Printer
Brand: Xerox Pages: 3
VTech Baby 546103 Instruction Manual preview
546103
Brand: VTech Baby Pages: 22
Obelink TREFFER MINI Pitching Instruction preview
TREFFER MINI
Brand: Obelink Pages: 2
Larson Electronics ALU-TP-158 Instruction Manual preview
ALU-TP-158
Brand: Larson Electronics Pages: 2
yasuni TUB653 Assembly Instructions Manual preview
TUB653
Brand: yasuni Pages: 8
Izzo Golf Big Daddy Insta-Net Manual preview
Big Daddy Insta-Net
Brand: Izzo Golf Pages: 2
Pro-Ject Audio Systems usb box Instructions For Use Manual preview
usb box
Brand: Pro-Ject Audio Systems Pages: 7
SOLAC ID7840 Instructions For Use Manual preview
ID7840
Brand: SOLAC Pages: 13

Brands by name

Popular brands

Load more brands