manualshive.com logo in svg

HTC GL 35 D, Manual, Page: 35 / 50

Share
Download
HTC GL 35 D Manual Download Page 35

HTC GL 35 D

Maintenance and repairs

1.0

29

5

Maintenance and repairs

5.1

General

We recommend regular inspection of the dust extractor.

Warning!

Disconnect the electrical supply when cleaning, carrying out maintenance or
repairing the machine.

Warning!

Use protective equipment such as safety shoes, safety goggles, protective
gloves, mouth mask and hearing protection.

5.2

Cleaning

Warning!

Do not rinse off the machine using a high-pressure washer, as moisture can
penetrate to the electrical parts and the absolute filter and sock filter, as well as
damage the drive system and the duct fan.

•

Always clean the machine after use with a damp sponge or cloth.

5.3

Daily

5.3.1

Check HEPA filters

Note!

When checking the HEPA filter , the dust extractor must be placed in the
operating position.

Warning!

The dust that is sucked up is harmful if inhaled. Follow local regulations and
use breathing protection.

1.

Undo the two quick fasteners (1) that hold the HEPA filter in place, see Figure 5-1,
page 

30

.

Summary of Contents for GL 35 D



















































Reviews:

No comments