Never push the equipment beyond its design limits.
If it will not do what you want with reasonable ease and
speed, assume you have the wrong heater for the job.
Contact your local HSS Hire Shop for advice.
Keep the equipment clean
- you will find this less of a
chore if you clean it regularly, rather than wait until the end
of the hire period.
When not in use
, store the equipment somewhere
clean, dry and safe
from thieves.
Set the switch to ‘fan only and wait for the unit to
cool down.
Once cool switch the supply OFF and unplug it from
the power supply.
All that remains is to give the unit a final clean up
ready for return,
to your local HSS Hire Shop.
Code 56144 / 56145
Three Phase
9KW and
18KW Heaters
Three phase fan type heaters offering two
heat settings and one ‘fan only’ setting.
Operating & Safety Guide 892
892/02
©HSS Hire Service Group Ltd 2004 No. 892/02
Group Office: 25 Willow Lane, Mitcham, Surrey CR4 4TS
Web Site: http://www.hss.com
...any comments?
If you have any suggestions to enable us to improve
the information within this guide please fax your
comments or write to the Product Manager at the
address below
Fax: 020 8687 5001
EQUIPMENT CARE
FINISHING OFF
The heater has a three position switch, ‘0’ for fan
only, ‘1’ for 9Kw heat output, and ‘2’ for 18Kw heat
output.
Note that
when the unit is connected to a power
supply and the supply is switched ON, the fan will
run in all three switch positions.
Only when set to No
1 or 2 will heat be emitted
Having double-checked that the heater switch is set to the
‘0’ (fan only position),
plug the heater into its power
supply and switch the supply ON.
Model 1…
Start by setting the switch to position ‘1’,
this will
activate the fan without heat.
Check that the fan is
running BEFORE you move the switch to position ‘2’
(the 6.5Kw heat setting).
If the fan fails to run,
DISCONNECT THE UNIT AND
SWITCH THE SUPPLY OFF then
contact your local HSS
Hire Shop for advice.
Once
you have confirmed that
the fan is running move
the switch to position ‘2’,
this will give an output of
6.5Kw and may prove to be sufficient for your needs.
If
setting ‘2’ proves
insufficient, move the switch to
position ‘3’.
Always
avoid using more heat than is required
and
keep an eye on the room temperature as the heat builds
up.
When you want
to switch the unit OFF, turn the
switch to position ‘1’ and leave the unit for at least 5
minutes.
In this position,
only the fan will run and
will
help
cool down the heating element
before you handle
the unit.
The ‘fan only’ setting can be used
if you wish
to
circulate air without heating it.
Model 2…
Check that the fan is running BEFORE you move the
switch to position ‘1’
(the 9Kw heat setting).
If the fan fails to run,
DISCONNECT THE UNIT AND
SWITCH THE SUPPLY OFF then
contact your local HSS
Hire Shop for advice.
Once
you have confirmed that
the fan is running move
the switch to position ‘1’,
this will give an output of 9Kw
and may prove to be sufficient for your needs.
If
setting ‘1’ proves
insufficient, move the switch to
position ‘2’.
Always
avoid using more heat than is required
and
keep an eye on the room temperature as the heat builds
up.
When you want
to switch the unit OFF, turn the
switch to position ‘0’ and leave the unit for at least 5
minutes.
In this position,
only the fan will run and
will
help
cool down the heating element
before you handle
the unit.
The ‘fan only’ setting can be used
if you wish
to
circulate air without heating it.
BASIC TECHNIQUES
