HSD WellStore, Manual

Page: 22 / 80

___________________________________________
ENGLISH
20
220 ÷ 240 VAC
50 - 60 Hz
50 W
1 - 3 Mhz
2,5 W/cm
2
0 ÷ 100%
10 ÷ 100%
Pulsed, continue
50 mm / 40 mm
6,15 cm
2
/ 3,79 cm
2
12 minuti
51
On the back of the device and on the ultrasound head, identification plates are
affixed with the technical data to be communicated to the Authorized Service
Center, the Manufacturer or the Dealer in the event of a request for information
or technical assistance.
70 mm
210 mm
320 mm
3 kg
POWER SUPPLY
FREQUENCY POWER SUPPLY
ABSORBED POWER
ELECTRIC INSULATION CLASS
TYPE OF PARTS APPLIED
WORKING FREQUENCY ULTRASOUND
MAXIMUM OUTPUT POWER
POWER REGULATION
MODULATION FREQUENCY
MODULATION TYPE
DIAMETER OF THE EMITTER SURFACE
ACTUAL RADIATION AREA TIMER MAX
THERAPEUTIC PROGRAMS
ENVIRONMENTAL CONDITIONS ALLOWED FOR OPERATION
TEMPERATURE [T]
HUMIDITY [Ur]
+10 ÷ +40 °C
30 ÷ 75 %
ATMOSPHERIC PRESSURE [mbar] da 700 a 1060 mbar
A
B
C
D
G
H
I
I
Damage, removal or alteration of the identification plate must be immediately
reported to the Manufacturer, the Authorized Service Center or the Dealer.
Warranty interventions will not be possible if the identification plate is
damaged, removed or altered.
B
Maker.
CE marking.
Attention, consult
the attached
documentation.
Physiological
effects: elevated
temperature.
BF Type of
applied parts
F
Device
class II.
Technical data.
Model, serial
number and year.
Identification
D F G L
TEMPERATURE [T] 0 ÷ 40 °C
HUMIDITY [Ur] 25 ÷ 75 %
C
E Consult the
Instructions for Use.
HEAD 50 MM
HEAD 40 MM
DEVICE
Technical data
i
Information
L Waste disposal:
treat separately
from household
waste.
ENVIRONMENTAL CONDITIONS ALLOWED FOR TRANSPORT AND
STORAGE
For the transport and storage of the appliance the following
environmental conditions are recommended:
A
A
HEAD 40 MM TIP
HEIGHT
DEPTH
WIDTH
WEIGHT
DIMENSIONS AND WEIGHT
C D H
I
B
DOUBLE HEAD DIFFUSER
E H
II
BF
CONNECTION OF THE
TREATMENT HEAD
Insert the connector of the treatment
head into the socket provided on the
front panel paying attention to the
insertion guide.
It is forbidden to use the device in
atmospheres that may contain
flammable and / or anesthetic gases.
!
Caution
The installation of the device is prohibited:
- in humid environments;
- near large quantities of water;
- near heat sources;
- in direct sunlight.
Remove the appliance
from the packaging and
place it on a stable
horizontal rigid surface,
suitable for supporting
its weight, near a power
outlet.
The space around the
appliance must not be
less than 20 centimeters
on all sides.
Never connect and disconnect the treatment head when the device
is on.
!
Caution
Put in action
CONNECTION TO THE ELECTRICITY NETWORK
power supply can damage it
without consequences for the
user). The use of the
appliance not properly
!
Caution
Do not use multiple plugs or power adapters.
Connect the appliance to a tested and efficient socket, equipped with
earth.
If in doubt, do not connect the device.
Check that the mains voltage corresponds to the indicated voltage and
frequency
on the nameplate of the appliance
12 13
(an incorrect voltage of the
connected to the mains
it could be dangerous.
Before inserting the
14
power supply into the socket
current make sure that the n-
ignition switch is positioned on “0” (zero).
Insert the power cable in housing "12" near the switch "13", making sure
that it is fully inserted. Insert the connection plug into the socket.
!
Caution
To avoid strangulation and suffocation with the power cord: mount
the unit and the power cord away from the face and out of the
reach of children.