HSD Well Store Dual Mag, Manual

Page: 39 / 80

EN
39
The device can simultaneously
manage 2 low frequency magnetic
diffusers,
2 High Frequency magnetic
speakers and 1 additional output
High Frequency for use with mats
or dedicated accessories.
The aforementioned speakers and
accessories share the same
program and the two Low and High
frequency sections can be enabled
and disabled separately by using
the relative “START / STOP”
buttons.
The device supports 96 different
programs to intervene on various
treatable pathologies.
When switched on, by placing the
switch in position "1", the green
"ON" LED lights up to confirm the
correct electrical connection. The
presentation text appears scrolling
on the display:
H S D
M A G N E T O T E R A P Y L F H F
Below, on the second line of the
display, the version of the
software installed in the machine
and the issue date are displayed
for a few seconds:
H S D
1 . 0 0 1 1 N O V 1 1
At the end of the previous
display, an invitation to choose
a treatment program appears:
C H O O S E
P R O G R A M
At this point, using the
“PROGRAMS ▲ / ▼” keys, one of
the 96 available programs can be
selected. The display shows the
program number and name
• PREPARATION AND EXECUTION OF PROGRAMS
METHOD OF USE
of the Pathology:
P R O G R A M 1 6
C E
R V
1 6 C V I C A L
B : 4 5 ’ 0 3 5 G 0 2 0 F
And of the High Frequency:
1 6 C
V I C A L
H : 4 5 ’ 1 2 5 0 F
In this phase the led bar indicates
the emitted power relative to the
two sections Low and High
frequency. The two sections are
independent, so I can act on the
respective START / STOP buttons.
In case
a section is in ACTIVE phase, by
pressing the relative START / STOP
key you can put it in “PAUSE
PHASE”: the “PAUSE” led starts
flashing and the “ACTIVE” led turns
off. The Buzzer also signals this
condition with continuous close
notes.
I will then be able to have a section
in ACTIVE PHASE and a section
in PAUSE PHASE; during the
displaying the data relating to the
section, the ACTIVE and PAUSE
LEDs will switch on appropriately.
Both during the ACTIVE PHASE and
during the PAUSE PHASE, by
pressing and holding one of the two
START / STOP keys for two
seconds, the treatment program is
definitively interrupted.
The Buzzer will emit three notes
close together, the ACTIVE and
PAUSE LEDs turn off and the STOP
LED lights up. At the same time the
display shows:
P R O G R A M
E N D E D
If, on the other hand, the current
treatment ends when the
programmed time has elapsed, the
Buzzer emits a long note and the
display shows:
P R O G R A M
E N D E D
VERSION ISSUING DATE
PATHOLOGY NAME
Once the program has been
selected and the speakers /
accessories to be used have been
connected, I start the Low
Frequency section using the
"START / STOP LF" key, while the
"START / STOP HF" key starts the
High Frequency section. In this
case, the “ACTIVE” led also lights
up to indicate that one or both
sections are in operation.
During the ACTIVE phase, the
display shows the group, the
program of the group and the
name of the pathology in the first
line and in the second line,
alternately,
the programmed parameters of the
Low Frequency section:
GROUP PROGRAM
REMAINING
TIME
LF
MAGNET
INTENSITY
PATHOLOGY
PATHOLOGY
PROGRAM
PROGRAM
Once the current program is
finished or interrupted, the
machine goes back to the
“CHOOSE A PROGRAM” point, the
STOP led goes out and only the ON
led remains lit.
At this point you can select a new
treatment, otherwise you can turn
off the device by placing the power
switch in the "0" state.
CAUTION!
Handle the treatment diffusers
with care. Careless handling can
affect their characteristics.
Do not knot or twist the connection
cable.
Do not use near the device and the
spray, liquid or solvent treatment
diffusers.
__________________________________________________________
I C A L
E R
E R
HF
MAGNET
FREQUENCY
REMAINING
TIME
HF
MAGNET
FREQUENCY