HPF H7-90-AT Manual Download Page 16

Page 

16

 of 

17

 

 

Warranty   

 

 

 

 

 

 

 

    

 

I. General Warranty 

Water Filter Systems¹ (Excluding consumables) Manufactured or Assembled² by High Performance Filtration (HPF) 

are covered under a 12-month Warranty Against Defects (Manufacturer’s Warranty). This warrants the water filter 

system to be free from defects in material and workmanship for a period of 12 months from date of sale. 

If applicable, HPF may cover the return freight in the form of a re-imbursement after the system has been inspected 

and confirmed it is a valid warranty claim. 
HPF will not cover any labour charge incurred by the consumer for the replacement or repair of a product. The 

warranty is strictly parts only for the parts supplied by HPF. This warranty only applies to the original consumer of the 

product and is non-transferable. If you have purchased the system through a re-seller, please contact them to 

facilitate the warranty on your behalf. All replaced or exchanged parts become the property of HPF. 

HPF does not cover the workmanship of the plumber who originally installed the system. Responsibility for damages 
that occur during installation fall with the plumber. 

 

II. Qualification for Warranty 

As per Australian Plumbing Codes, all filter systems must be installed by a qualified plumber. The consumer is 

responsible for keeping record and proof of installation in the form of an invoice and/or receipt. 

Filter systems must be maintained as per HPF recommendations³ including the use of replacement filters, fittings and 

components supplied by HPF. Failure to maintain the filtration systems using HPF supplied/approved products may 

void warranty. 

The warranty only applies if the product was used and/or installed in accordance with the user guide and/or 

installation instructions. This warranty is given in lieu of all other express or implied warranties and manufacturer 

shall in no circumstance be held liable for damages consequential or otherwise or delays caused or faulty 
manufacturing except as excluded by law. 

Warranties need to be approved by HPF to ensure the product was not incorrectly used, installed, or claimed. False 

and incorrect claims will be pursued at HPF’s discretion including chargeable inspection and transit costs incurred.  

HPF does not take responsibility for retaining customer records, it is the consumer’s responsibility to retain all 

invoices or proof of purchase from the original sale and ongoing maintenance records as proof of upkeep. 
 

III. Exclusions 

HPF Standard Warranty shall be void if the product sustains damage or failure resulting from any of the following: 

 

If the system was not installed in accordance with the manufacturers instruction manual. 

 

If your system(s) fails to be maintained in accordance with recommended servicing and as per the 

manufacturers operating instructions. 

 

Cross threading or damage to screws and/or threads 

 

Unauthorised or abnormal use or operation. 

 

Exposure to unsuitable environmental conditions*. 

 

Warranty – Australia 

This warranty is given by High Performance Filtration (Jacknel Pty Ltd ATF The J & N Family Trust). ABN 64 855 305 

562 Located at 7/38 Jade Drive, Molendinar QLD 4214. Ph 07 5597 6142 & email [email protected] 

This warranty is provided in addition to other rights and remedies you have under law. Our products come with 

guarantees which cannot be excluded under the Consumer Guarantees Act. 
 

IV. Extended Warranty 

The H7-90 UV system is eligible for a conditional extended 4-year warranty (commencing no later than 12 months 
from the sale date), to provide a total warranty period of 5 years. This extended warranty is subject to terms and 

conditions outlined below. This extended warranty covers the below parts of the system. 

 

Ultraviolet Chamber 

 

 

rev 1.0 | 30/09/2021

 

Summary of Contents for H7-90-AT


















Reviews: