background image

Operations

Power down the cartridge

Review the following information before powering down the cartridge:

• Before powering down a cartridge for any upgrade or maintenance procedures, always perform a

backup of critical cartridge data and programs.

• Depending on the cartridge model, the cartridge may be a single-node or a multi-node cartridge.

Always power down all nodes on the cartridge before removing it from the chassis.

• If you are powering down one node but leaving other nodes in a powered up state on the cartridge, the

cartridge power LED will remain illuminated, indicating at least one node is powered up.

Cartridges can be powered down individually and as a group of all cartridges in the chassis. Choose the
procedure in this section that fits your need.

When entering cartridge commands provided in this section, you can use one command to address
multiple cartridges. Use commas to separate non-contiguous numbers (omit spaces), or a dash to denote
a range (for example, C1,3-9N1-4). For more information about using commands, see the 

HPE Moonshot

iLO Chassis Management CLI User Guide

 in the Hewlett Packard Enterprise Information Library (

http://

www.hpe.com/info/moonshot/docs

).

Power down a cartridge remotely

Procedure

1. Log in to the iLO CM firmware

 on page 17.

2.

Power down the cartridge by issuing the appropriate command:

• For a cartridge running a functioning OS:

◦ Single node:

set node power off shutdown C<x>N<y>

◦ Multiple nodes (4):

set node power off shutdown C<x>N1-4

• For a nonresponsive system or when an OS has not been installed:

◦ Multiple nodes (4):

set node power off force C<x>N1-4

• For all cartridges:

set node power off force all

3.

Verify that the power is off by issuing the following command:

show node power {CxNy}

Power down a cartridge locally

Procedure

1. Log in to the iLO CM firmware

 on page 17.

2.

Power down the cartridge according to the current cartridge state:

• If the cartridge power LED is green, press and release the cartridge power button.

10

 Operations

Summary of Contents for ProLiant m710x



























































Reviews: