HPE ProLiant DL388 Gen10 Maintenance And Service Manual Download Page 113 | Manualshive

Page: 113 / 169

background image

**If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the
system health status.

†Facility power is not present, power cord is not attached, no power supplies are installed, power supply
failure has occurred, or the power button cable is disconnected.

UID button functionality

The UID button can be used to display the Server Health Summary when the server will not power on. For
more information, see the latest

HPE iLO 5 User Guide

Hewlett Packard Enterprise website

Front panel LED power fault codes

The following table provides a list of power fault codes, and the subsystems that are affected. Not all power
faults are used by all servers.

Subsystem

LED behavior

System board

1 flash

Processor

2 flashes

Memory

3 flashes

Riser board PCIe slots

4 flashes

FlexibleLOM

5 flashes

Removable HPE Smart Array SR Gen10 controller

6 flashes

System board PCIe slots

7 flashes

Power backplane or storage backplane

8 flashes

Power supply

9 flashes

Systems Insight Display LEDs

The Systems Insight Display LEDs represent the system board layout. The display enables diagnosis with the
access panel installed.

Component identification

113

«
...
111
112
113
114
115
...
»

Summary of Contents for ProLiant DL388 Gen10










































































































































































Reviews:

No comments

Related manuals for ProLiant DL388 Gen10

Brand: IBM Pages: 214

Brand: Ganz Pages: 5

Brand: Velvac Pages: 55

xPort Pro XPP1004000-02R

Brand: Lantronix Pages: 17

Brand: AIC Pages: 64

Aironet 1500 Series

Brand: Cisco Pages: 8

7835-H2 - Media Convergence Server

Brand: Cisco Pages: 8

APP1000 - One Application Server Appliance

Brand: Cisco Pages: 20

Brand: Cisco Pages: 130

Brand: Excito Pages: 3

Brand: Axis Pages: 129

Brand: DM&P Group Pages: 27

Brand: Meinberg Pages: 112

Brand: Star Lake Pages: 50

Codec Engine Server

Brand: Texas Instruments Pages: 36

Brand: IBM Pages: 8

Brand: New H3C Technologies Pages: 45

Brand: Intel Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands