HP XP User Manual Download Page 95

Page: 95 / 148

Recommended action

Perform the following using Storage Management Software:

•

(1) Delete any Business Copy pairs which are not used when the number of Business Copy
pairs has reached the maximum.

•

(2) Delete any S-VOLs which are not used when the number of S-VOLs for P-VOL has
reached the maximum.

E10000F7

Message

Creation of S-Vol failed. The specified RaidGroup is not valid. Creation of S-VOL failed.

Explanation

Creation of S-Vol failed. The specified RaidGroup is not valid. Creation of S-VOL failed.

Recommended action

The specified Raid/ParityGroup is not valid. The specified RAID/Parity group is not valid. See

“About errors attributable to disk array systems” (page 133)

E10000F8

Message

Creation of S-Vol failed. The LU cannot be created.

Explanation

Creation of S-VOL failed.

Recommended action

Perform the following using Storage Management Software:

In addition, delete any unused LUs in cases (1)-(3) below.

•

(1) Check whether the number of LUs in the disk array system has reached the maximum.

•

(2) Check whether the number of LUs in the RAID/Parity group or THP (Smart) pool has
reached the maximum.

•

(3) Confirm that the available space of the specified RAID/Parity group or THP (Smart) pool
is sufficient.

•

(4) When you use Account Authentication, confirm that Storage Administrator (View and
Modify) authority is assigned to the user account. If it is not, assign it.

E10000FB

Message

Failed to delete S-Vol:[ LU number of S-VOL] failed. The specified LU is in regressed status.

Explanation

Creation of S-VOL failed.

Recommended action

A failure occurred in the specified RAID/Parity group or THP (Smart) pool. Remove the failure,
then re-execute.

Error messages

Summary of Contents for XP





















































































































































Search results

Summary of Contents for XP

Reviews:

Related manuals for XP

Brands by name

Popular brands

HP XP, User Manual

Search results

Summary of Contents for XP

Reviews:

Related manuals for XP

Brands by name

Popular brands