HP XP User Manual Download Page 124

Page: 124 / 148

Recommended action

•

(1) Confirm the IP address or serial number of the disk array system using Storage
Management Software, and set them in the proper format in the setup file (See Subsection
3.2.1).

•

(2) Confirm that the LAN cables are connected properly.

•

(3) Confirm that the Password Protection function of the disk array system is set to disabled.

E20020CF

Message

Creation of S-Vol failed: The P-Vol already has an active pair.

Explanation

Creation of an S-VOL failed.

The pair status of the LU is Copy.

Recommended action

The pair status of the specified LU is Copy. Specify a useable LU and re-execute.

E20020D1

Message

Creation of S-Vol failed: No more pairs can be created.

Explanation

Creation of S-VOL failed. No more S-VOLs can be created.

Recommended action

•

(1) Delete any unused Business Copy pairs when the number of Business Copy pairs has
reached the maximum.

•

(2) The number of S-VOLs for P-VOL has reached the maximum. Delete S-VOLs which are
not being used.

E20020D2

Message

Creation of S-Vol failed: The specified RaidGroup is not valid.

Explanation

Creation of an S-VOL failed.

The specified RAID/Parity group is not valid.

Recommended action

The specified RAID/Parity group is not valid. See

“About errors attributable to disk array systems”

(page 133)

E20020D3

Message

Creation of S-Vol failed: Valid RaidGroups are not available. .

124

Troubleshooting

Summary of Contents for XP





















































































































































Search results

Summary of Contents for XP

Reviews:

Related manuals for XP

Brands by name

Popular brands

HP XP, User Manual

Search results

Summary of Contents for XP

Reviews:

Related manuals for XP

Brands by name

Popular brands