manualshive.com logo in svg

HP Tc2120 - Server - 256 MB RAM, Installation Manual, Page: 71 / 92

Share
Download
HP Tc2120 - Server - 256 MB RAM Installation Manual Download Page 71

 

Video Configuration 

• 

Red Hat will detect your chip as an 

ATI Mach64

 chip. However, the HP Server 

tc2120 ships with an 

ATI Rage XL

 AGP chipset. Modify the settings in order to 

correctly configure the video settings. 

Monitor Selection 

• 

The installation program will attempt to detect the monitor being used; otherwise, 
you can find HP monitor references on the back of your monitor. 

Custom X Configuration 

• 

HP recommends selecting login type as “Graphical.” Click 

Next

 to continue. 

Congratulations 

• 

Click 

Exit

 to exit the installation program. Remove the CD from the drive. 

• 

The system reboots and loads your new Red Hat environment. 

Section 2. Install Additional HP Accessories 

The hp server tc2120 Startup CD includes the drivers for the following HP 
accessories: 

• 

HP-Intel 10/100 LAN 

• 

HP-Intel 10/100/1000 LAN 

• 

HP IDE RAID 

• 

HP v92 56k Modem 

Please refer to the product manual enclosed with your accessory for the detailed 
installation procedure and/or the attached readme.txt file associated with the driver. 
The readme.txt file can be found included on the appropriate driver diskette. 

On-Line Information and Software Sources 

• 

HP World Wide Web access: 

http://www.hp.com/

 

 

71 

  

HP CONFIDENTIAL

 

Writer: Jimmy Chan File Name: 312977-006.doc 

Codename: Condor II Part Number: 312977-006 Last Saved On: 9/10/03 10:05 AM 

Summary of Contents for Tc2120 - Server - 256 MB RAM





























































































Reviews:

No comments