manualshive.com logo in svg

HP Tc2120 - Server - 256 MB RAM, Installation Manual, Page: 68 / 92

Share
Download
HP Tc2120 - Server - 256 MB RAM Installation Manual Download Page 68

 

Phase 2 — Configure the Server 

Welcome to Red Hat Linux 

Click on 

Next

 to continue. 

 

NOTE:

  Using the GUI installation, you will have an on-screen description of each possible 

selection displayed on the left of the screen. 

Language Selection 

Select the appropriate language. Click 

Next

 to continue. 

Keyboard Selection 

Please note the following recommendations: 

• 

Your HP server comes with a Generic 104-key PC keyboard and 2-Button Mouse 
(PS/2). 

 

NOTE:

  If you wish to change your keyboard type after you have booted your Red Hat Linux 

system, you may use the /usr/sbin/kbdconfig command. 

Mouse Configuration 

• 

See note above. Click 

Next

 to continue. 

Installation Type 

• 

HP recommends selecting a Custom installation type, because this mode allows 
for the most flexible installation. 

Disk Partitioning Setup 

• 

HP recommends using the default partitioning mode: Automatically partition 
(You will need to select the drives to install to and then select “Remove all 
partitions on this system” after clicking 

Next

. 

68

 

 

 

HP CONFIDENTIAL

 

Writer: Jimmy Chan File Name: 312977-006.doc 

Codename: Condor II Part Number: 312977-006 Last Saved On: 9/10/03 10:05 AM 

Summary of Contents for Tc2120 - Server - 256 MB RAM





























































































Reviews:

No comments