HP Tc2120 - Server - 256 MB RAM Installation Manual Download Page 86 | Manualshive

Page: 86 / 92

HP Tc2120 - Server - 256 MB RAM Installation Manual Download Page 86

•

Modem 56k v92

•

Promise IDE RAID PCI

•

HP Adaptec 29160 SCSI Controller

Please refer to the product manual enclosed with your accessory for the detailed
installation procedure and/or the attached readme.txt file associated with the driver.
The readme.txt file can be found included on the appropriate driver diskette.

On-Line Information and Software Sources

•

HP World Wide Web access:

http://www.hp.com

•

Red Hat World Wide Web access:

http://www.redhat.com

Installing SuSE Linux 7.3

Prepare the Installation

Please refer to the Chapter 1 "Preparing the HP Server tc2120 for NOS Installation"
for our recommendations on server preparation. Then gather the following material:

•

HP Server tc2120 Startup CD

•

SuSE Linux 7.3 CD-ROM #1 #2 #3 and #4

•

Two or more clients for testing purposes (Optional)

High Level Process Flow

1.

Perform SuSE Linux 7.3 installation.

2.

Install additional HP accessories.

86

HP CONFIDENTIAL

Writer: Jimmy Chan File Name: 312977-006.doc

Codename: Condor II Part Number: 312977-006 Last Saved On: 9/10/03 10:05 AM

«
...
84
85
86
87
88
...
»

Summary of Contents for Tc2120 - Server - 256 MB RAM





























































































Reviews:

No comments