HP StorageWorks A7298A Installation Manual Download Page 65

Page: 65 / 92

Host Bus Adapter for Windows and Linux Installation Guide

Diagnostic and Configuration

Utilities

This chapter contains instructions for installing and using the following Windows
NT and Windows 2000 utilities:

■

DOS Diagnostic utility, x86DNLD, a DOS-based diagnostic and firmware
download utility. This utility is used exclusively in standalone environments.

■

LightPulse Utility/NT, LP6DUTIL is a Windows-based graphical user
interface for updating firmware and Boot code. This utility is used in Software
Solution kits.

Note:

The diagnostic and firmware download utility is used to upgrade firmware on

both Host Bus Adapter (HBA) environments.

Summary of Contents for StorageWorks A7298A





























































































Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands

HP StorageWorks A7298A, Installation Manual

Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands