HP StorageWorks A7298A Installation Manual Download Page 13

Page: 13 / 92

About this Guide

Host Bus Adapter for Windows and Linux Installation Guide

Getting Help

If you still have a question after reading this guide, contact an HP authorized
service provider or access our website:

http://www.hp.com

HP Technical Support

Telephone numbers for worldwide technical support are listed on the following
HP website:

http://www.hp.com/support/

. From this website, select the country

of origin.

Note:

For continuous quality improvement, calls may be recorded or monitored.

Be sure to have the following information available before calling:

■

Technical support registration number (if applicable)

■

Product serial numbers

■

Product model names and numbers

■

Applicable error messages

■

Operating system type and revision level

■

Detailed, specific questions

HP Storage Website

The HP website has the latest information on this product, as well as the latest
drivers. Access storage at:

http://www.hp.com/country/us/eng/prodserv/

storage.html

. From this website, select the appropriate product or solution.

HP Authorized Reseller

For the name of your nearest HP authorized reseller:

■

In the United States, call 1-800-345-1518

■

In Canada, call 1-800-263-5868

■

Elsewhere, see the HP website for locations and telephone numbers:

http://www.hp.com

Summary of Contents for StorageWorks A7298A





























































































Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands

HP StorageWorks A7298A, Installation Manual

Search results

Summary of Contents for StorageWorks A7298A

Reviews:

Related manuals for StorageWorks A7298A

Brands by name

Popular brands