HP ProLiant XL230a Gen9 User Manual Download Page 56 | Manualshive

Page: 56 / 80

background image

Software and configuration utilities 56

NOTE:

The server ships with the same version programmed on each side of the ROM.

Safety and security benefits

When you flash the system ROM, ROMPaq writes over the backup ROM and saves the current ROM as a
backup, enabling you to switch easily to the alternate ROM version if the new ROM becomes corrupted for

any reason. This feature protects the existing ROM version, even if you experience a power failure while
flashing the ROM.

Keeping the system current

Access to HP Support Materials

Access to some updates for HP ProLiant Servers may require product entitlement when accessed through the
HP Support Center support portal. HP recommends that you have an HP Passport set up with relevant

entitlements. For more information, see the HP website

Drivers

IMPORTANT:

Always perform a backup before installing or updating device drivers.

The server includes new hardware that may not have driver support on all OS installation media.
If you are installing an Intelligent Provisioning-supported OS, use Intelligent Provisioning (on pag e

) and its

Configure and Install feature to install the OS and latest supported drivers.
If you do not use Intelligent Provisioning to install an OS, drivers for some of the new hardware are required.
These drivers, as well as other option drivers, ROM images, and value-add software can be downloaded as

part of an SPP.
If you are installing drivers from SPP, be sure that you are using the latest SPP version that your server
supports. To verify that your server is using the latest supported version and for more information about SPP,

see the HP website To locate the drivers for a particular server, go to the HP website on

Drivers, Software & Firmware

. Then, enter your product name in the

Find an HP product

field and click

Go

.

Software and firmware

Software and firmware should be updated before using the server for the first time, unless any installed
software or components require an older version.
For system software and firmware updates, use one of the following sources:

•

Download the SPP ("

HP Service Pack for ProLiant

" on page

) from the HP Service Pack for ProLiant

download page

«
...
54
55
56
57
58
...
»

Summary of Contents for ProLiant XL230a Gen9

















































































Reviews:

No comments

Related manuals for ProLiant XL230a Gen9

Brand: IBM Pages: 40

NetVista N2800e

Brand: IBM Pages: 82

Brand: QNAP Pages: 39

Brand: sysmik Pages: 2

Brand: N-Tron Pages: 55

Brand: IBM Pages: 100

Brand: Santec Pages: 40

Brand: Abit Pages: 56

Brand: t.a.c. Pages: 36

Brand: MRV Communications Pages: 65

UniServer R4300 G6

Brand: H3C Pages: 542

LANTIME M300/MGR

Brand: Meinberg Pages: 5

Brand: Inspur Pages: 37

5325301507 - Snap Server 4400 NAS

Brand: Adaptec Pages: 250

Brand: B+B SmartWorx Pages: 2

EtherneTV-NXG 1

Brand: VBrick Systems Pages: 21

Brand: GIGA-BYTE TECHNOLOGY Pages: 90

DataSafe Network Device

Brand: Iomega Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands