manualshive.com logo in svg

HP ProLiant BL460c Gen9, User Manual, Page: 28 / 90

Share
Download
HP ProLiant BL460c Gen9 User Manual Download Page 28

 
 

Setup  28 

Two types of interconnect modules are available for BladeSystem c-Class enclosures: Pass-Thru 
modules and switch modules. For more information about interconnect module options, see the Hewlett 
Packard Enterprise website (

http://www.hpe.com/servers/blades/interconnects

). 

   

 

IMPORTANT:

  To connect to a network with a Pass-Thru module, always connect the 

Pass-Thru module to a network device that supports Gigabit or 10 Gb speed, depending on the 
corresponding Pass-Thru model. 

   

 

Install the server blade 

   

 

CAUTION:

  To prevent improper cooling and thermal damage, do not operate the server 

blade enclosure unless all bays are populated with either a component or a blank.   

   

   

 

CAUTION:

  Failure to install the divider in a quadrant when installing half-height blades can 

result in damage to the connectors on the server blades.   

   

For the best possible BladeSystem and Virtual Connect experience, and to prevent a future reboot, 
Hewlett Packard Enterprise requires updating the Onboard Administrator and Virtual Connect to the 
correct version before installing a ProLiant Gen9 server blade. The version information is located on the 
tag on the front of the server blade. 

For more information on this and other specific firmware and driver requirements, as well as the latest 
firmware and driver versions, download the SPP on the Hewlett Packard Enterprise website 
(

http://www.hpe.com/servers/spp/download

). 

1. 

Remove the device bay blank. Retain the blank for future use. 

 

Summary of Contents for ProLiant BL460c Gen9



























































































Reviews:

No comments