HP ProDesk 400 G4 Maintenance And Service Manual Download Page 49

Page: 49 / 132

System board

NOTE:

The system board spare park kit includes replacement thermal material.

Follow these steps to remove the system board:

Prepare the computer for disassembly (see

Preparation for disassembly on page 21

Remove the access panel (see

Access panel on page 22

), and then remove the following components:

Drive cage (see

Drive cage on page 29

)

Serial port module (see

Serial port module on page 27

)

Fan-sink (see

Fan-sink on page 38

)

NOTE:

When replacing the system board, be sure that the processor (see

Processor on page 40

) is

removed from the defective system board and installed on the replacement system board.

Disconnect the following cables from the system board:

(1) Power supply cables (from three locations)

(2) Fan cable

(3) Speaker cable

(4) Drive power cable

(5) Drive data cables (from three locations)

System board

Summary of Contents for ProDesk 400 G4





































































































































Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands

HP ProDesk 400 G4, Maintenance And Service Manual

Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands