HP ProDesk 400 G4 Maintenance And Service Manual Download Page 12

Page: 12 / 132

Illustrated parts catalog

Serial number location

Each computer has a unique serial number and a product ID number that are located on the exterior of the
computer. Keep these numbers available for use when contacting support for assistance.

Computer major components

Description

Access panel:

For use on computer models in all country and regions except the People’s Republic of China

For use on computer models only in the People’s Republic of China

Front bezel:

For use on computer models in all country and regions except the People’s Republic of China

For use on computer models only in the People’s Republic of China

Blank bezel

System boards (includes replacement thermal material):

For use on HP ProDesk 480 G4 MT computer models:

Equipped with the Windows 10 operating system for use in the People’s Republic of China

Equipped with a non-Windows operating system for use in the People’s Republic of China

Equipped with NetC operating system and PCI slots for use in the People’s Republic of China

For use on HP ProDesk 400 G4 MT computer models:

Chapter 2 Illustrated parts catalog

Summary of Contents for ProDesk 400 G4





































































































































Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands

HP ProDesk 400 G4, Maintenance And Service Manual

Search results

Summary of Contents for ProDesk 400 G4

Reviews:

Related manuals for ProDesk 400 G4

Brands by name

Popular brands