manualshive.com logo in svg

HP ProCurve 8116fl, Installation And Getting Started Manual

Share
Download
HP ProCurve 8116fl Installation And Getting Started Manual Download Page 87

Replacing Hardware 

Replacing Mini-GBICs 

Installing mini-GBICs 

The ProCurve mini-GBICs use slightly different release mechanisms, but the 
insertion process is virtually the same for all. 

To install a mini-GBIC in the 10-Port mini-GBIC Module: 

1.   Orient the mini-GBIC as shown in the illustration below. Note that the 

release mechanism is on the left of the receptacle. 

2.   Insert the mini-GBIC into the receptacle until it locks into position. 

C a u t i o n    

If the mini-GBIC does not go in easily, do not force it. If the mini-GBIC is 
not oriented properly, it will stop about one quarter of the way into the 
slot—remove and reorient the mini-GBIC so that it slides easily into the 
slot. 

Keep the dust plug in the mini-GBIC when there is no fiber cable plugged 
in. The optics will not work properly when obstructed with dust or 
contaminants. It is recommended that you clean the optic surfaces of the 
fiber cable prior to plugging it into the optical bores of the mini-GBIC. 

4-15 

R

e

pl

a

c

in

g H
a

rd

wa
re 

Summary of Contents for ProCurve 8116fl







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands