manualshive.com logo in svg

HP ProCurve 8116fl, Installation And Getting Started Manual

Share
Download
HP ProCurve 8116fl Installation And Getting Started Manual Download Page 75

Replacing Hardware 

Replacing Fan Trays 

Replacing Fan Trays 

The Fan Status LEDs on the switch chassis and on each fan try indicate when 
one or more fans fail. In this case, simply replace the failed component as soon 
as possible. 

W A R N I N G    

For safety, if you are hot swapping out the fan tray assembly, pull the assembly 
out one-inch and allow the fans to stop rotating before pulling it all the way out. 

To replace a fan tray

: 

1.   Remove the two screws holding the failed fan tray assembly. (The LED 

on the fan tray and on the chassis will indicate which one is failed.) 

2.   Pull the fan tray assembly out. 

3.   Install the new fan tray assembly as described on 

page 2-15

. 

N o t e    

In case your cabling installation does not allow access to the fan tray 
assemblies, remove as many cables as necessary in order to access them. 

4-3 

R

e

pl

a

c

in

g H
a

rd

wa
re 

Summary of Contents for ProCurve 8116fl







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands