manualshive.com logo in svg

HP ProCurve 8116fl, Installation And Getting Started Manual

Share
Download
HP ProCurve 8116fl Installation And Getting Started Manual Download Page 55

Installing the ProCurve Switch 8100fl 

Installation Procedures 

7. Verifying the Installation 

After you have installed all the appropriate components for your switch 
(power supplies, fan trays, and the various modules required for your 
installation), replace the power and slot covers over any empty power bays 
and module slots. Then power on the switch to verify that it is working 
properly by following the procedure described on 

page 2-30

. 

C a u t i o n    

For proper switch cooling and to reduce any electronic emissions, install the 
appropriate slot covers over any unused power bays and module slots. 

Failure to use the correct slot cover may result in improper switch cooling. 

Make sure that you use the correct type of cover for each empty slot. Each 
cover is labeled as follows to indicate the type of slot for which it is designed 
(part numbers shown in parentheses): 

■

 

FM Cover for Switch 8008fl fabric module slots (5069-0122) 

■

 

FM Cover for Switch 8016fl fabric module slots (5069-7937) 

■

 

MM Cover for management module slots (5069-0123) 

■

 

IM Cover for interface module slots (5069-0124) 

■

 

EM Cover for Switch 8116fl expansion module slots (5069-0125) 

The following illustration shows a fully loaded Switch 8108fl chassis

:

 

Inst

all
ing t
he Pro

C

u

rve  

Switch 8

100fl 

2-29 

Summary of Contents for ProCurve 8116fl







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands