![HP ProCurve 1600M Management And Configuration Manual Download Page 558](http://html.mh-extra.com/html/hp/procurve-1600m/procurve-1600m_management-and-configuration-manual_155305558.webp)
Monitoring and Analyzing Switch Operation
Traffic Mirroring
Using Interface Identity and Direction of Movement
To Select the Traffic To Mirror from a Source Switch
Use the commands in this section to configure mirrored traffic selection for
either local or remote mirroring. Options for the selection criteria includes:
■
Interface Options: VLAN, port, or trunk
■
Directional Options: entering or leaving the switch, or both
Port, Trunk, and/or Mesh Interface with Traffic Direction as the
Selection Criteria.
Use this command when the direction of traffic move
ment on the port, trunk, and/or mesh interface defines the criteria for mirror
ing traffic.
Syntax:
[no] interface <
port/trunk/mesh
> monitor all < in | out | both > mirror
< 1 - 4 |
name-str >
[< 1 - 4 |
name-str >
< 1 - 4 |
name-str >
< 1 - 4 |
name-str >
]
This command assigns a mirroring source to a previously
configured mirroring session on a source switch. It specifies the
port. trunk, and/or mesh source(s) to use, the direction of traffic
to mirror, and the session identifier.
The
no
form of the command removes a mirroring source
assigned to the session, but does not remove the session itself.
This enables you to repurpose a session by removing an
unwanted mirroring source and adding another in its place.
interface <
port/trunk/mesh
>:
Identifies the port(s), static
trunk(s), and/or mesh on which to mirroring traffic. Use a
hyphen for a range of consecutive ports or trunks (
a5-a8,
Trk2-Trk4
).
Use a comma to separate non-contiguous
interfaces (
b11,b14,Trk4,Trk7
).
monitor all < in | out | both >:
For the interface specified by
<
port/trunk/mesh
>
, selects traffic to mirror based on whether
the traffic is entering or leaving the switch on the interface.
in
:
Mirror entering traffic.
out
:
Mirror exiting traffic
.
both
:
Mirror traffic entering or exiting.
(Using
monitor
without mirroring criteria or session
number affects session 1. Refer to “Monitor Command” on
page B-71.)
—Continued—
B-48
Summary of Contents for ProCurve 1600M
