background image

© Copyright 2021 HP Development 
Company,  L.P. 

 

AMD is a trademark of Advanced Micro 
Devices,  Inc. Bluetooth is a trademark 
owned by its  proprietor and used by HP 
Inc. under license.  NVIDIA is a trademark 
and/or  registered trademark of NVIDIA 
Corporation in  the U.S. and other 
countries. USB Type-C and  USB-C are 
registered trademarks of USB 
Implementers Forum. DisplayPort and the 
DisplayPort logo are trademarks owned 
by the  Video Electronics Standards 
Association (VESA)  in the United States 
and other countries. 

 

The information contained herein is 
subject to  change without notice. The 
only warranties for  HP products and 
services are set forth in the  express 
warranty statements accompanying  such 
products and services. Nothing herein 
should be construed as constituting an 
additional warranty. HP shall not be liable 
for  technical or editorial errors or 
omissions  contained herein. 

 

First Edition: March 2021   

Document Part Number:  

L55527-

 

OMEN X 27-MSG-V1 

Assembly part number: L55527-001 

Product notice

 

 

Only trained service personnel familiar with 
this product should service it. Before 
performing any maintenance or service, be 
sure to read “Important Safety Information”.

 

Summary of Contents for L55527-001


























Reviews: