HP J4899B Installation And Getting Started Manual Download Page 30

Page: 30 / 116

2-10

Installing the Switch

Installation Procedures

sta

llin

itc

Check the LEDs on the switch as described below.

When the switch is powered on, it performs its diagnostic self test. Self test
takes approximately 50 seconds to complete.

LED Behavior

During the self test:

•

Initially, all the switch and port LEDs are on. Most of the LEDs go off
and then may come on again during phases of the self test.

•

For the duration of the self test, the Self Test LED stays on.

Self Test LED

Switch port LEDs

Power and

Fault LEDs

Switch 2650

Switch 2650-PWR

LED

Mode

Clear

Reset

Spd mode: off = 10 Mbps,

flash = 100 Mbps, on = 1000 Mbps

PoE-Ready 10/100Base-TX Ports (1 - 48)

Power

Fault

procurve

switch

2650-PWR

J8165A

PoE

Act

FDx

Link|M

Test

RPS
EPS
Fan

Status

Spd

PoE

Test LED

Summary of Contents for J4899B





















































































































Search results

Summary of Contents for J4899B

Reviews:

Brands by name

Popular brands

HP J4899B, Installation And Getting Started Manual

Search results

Summary of Contents for J4899B

Reviews:

Brands by name

Popular brands