HP J4861A Installation And Getting Started Manual Download Page 17 | Manualshive

Page: 17 / 94

HP J4861A Installation And Getting Started Manual Download Page 17

Introducing the HP ProCurve Series 4100gl Switches

Back of the Switch

Back of the Switch

.

AC power connector

slot for installing optional
redundant power supply

Power Connector

The Series 4100gl Switches do not have a power switch; they are powered on
when connected to an active AC power source. The switches automatically
adjust to any voltage between 100-127 and 200-240 volts and either 50 or 60
Hz. There are no voltage range settings required.

Slot for Redundant Power Supply

A second, load-sharing redundant power supply (HP ProCurve Switch gl/xl
RPS, HP J4839A) can be installed in the back of the Series 4100gl switches. To
provide true redundancy, this second power supply should be connected to a
different AC power source from the other supply. Then, if one AC power
source fails, the switch will continue to run.

C a u t i o n

The switch power supplies

are

hot swappable, but, as indicated by the caution

statement on the power supply, it

must

be disconnected from AC power

before being installed or removed.

Series 4100gl Switches

In

tro
duc

ing the

HP ProCurve

��

�

��

�

��

��

Because the switch can run on a single supply, removing a redundant supply
will not interrupt switch operation.

1-9

«
...
15
16
17
18
19
...
»

Summary of Contents for J4861A































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands