background image

HP Indigo press ws4000 Cluster 1 procedures 

proprietary and confidential 

CA293-00600, Rev 00 

page 18 of 221 

 

Figure 9  Connecting the cable to the ILD  

 

•6.  Release the Emergency Stop button and place the press in Standby mode. 

•7.  Insert the diskette or CD Rom into the computer.  

•8.  Configure your laptop computer to boot using the CD ROM or diskette.   

BIOS access and configuration is different for different computers.  Consult your 
computer documentation for instructions regarding the reconfiguration of the boot 
order in the BIOS.  The following is a typical procedure for accessing the BIOS for the 
ILD download. 

a.  Restart the laptop computer. 

b.  While the computer is turning on, click the key indicated to access the 

BIOS. The directions are usually found on the bottom of the screen 
when the computer is turning on. The most likely keys are F2, F12 or 
DEL and they differ for each computer. 

c.  After entering the BIOS screen: select the BOOT MENU or its 

equivalent. This may differ from computer to computer as well. 

d.  Select the appropriate device for the boot: CD ROM or diskette drive. 

 

After booting, the Flash Memory Loader Utility – Main Menu opens.  

•9.  Open and start the laptop computer.  The computer should boot using the 

diskette or CD ROM.  The 

Flash Memory Loader Utility – Main Menu

 

opens.  

Summary of Contents for Indigo Press WS4000






























































































































































































































Reviews: