manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Share
Download
HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 80

Installing an 

Installing an appliance module

appliance module

The appliance modules have specific population guidelines based on the  appliance module and the system configuration. As a best

practice, if two appliance modules of the same type exist in any group of linked frames, install the appliance modules in separate frames.

After all components are installed and cabled, be sure to reimage the  appliance module before bringing the  appliance module into your

HPE Synergy configuration. Updating the firmware, ensures that the appliance module is compatible with the HPE Synergy Software

Release installed on HPE Synergy. For more information, see Update the firmware.

Procedure

Procedure

1.  If installed, remove the  appliance module blank from the appliance bay.

2.  Install the first appliance module into appliance bay 1.

When the appliance module is fully seated, it locks into place.

Installing an appliance module

80

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands