HP HPE Synergy 12000 Frame Setup And Installation Manual Download Page 20

Page: 20 / 183

HPE Synergy configuration

An initial setup for HPE Synergy requires software release planning and planning the location for each component. To ensure a proper

configuration, review the information in the following documents on the Hewlett Packard Enterprise website (
http://www.hpe.com/info/synergy-docs

http://www.hpe.com/info/synergy-docs):

HPE Synergy Configuration and Compatibility Guide —This document helps to understand more about each component and the
configuration requirements for installing each component. It provides the following:

An overview of HPE Synergy management and fabric architecture

Detailed hardware component identification

Hardware configuration guidelines

Interconnect, power, and HPE Synergy Console cabling information

HPE Synergy Cabling Guide—This document provides detailed information and diagrams on how to cable HPE Synergy.

HPE Synergy Migration Guide—This document takes you through the steps to migrate to the latest offerings of appliances and
Frame Link Modules.

HPE Synergy configuration

Summary of Contents for HPE Synergy 12000 Frame
























































































































































































Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands

HP HPE Synergy 12000 Frame, Setup And Installation Manual

Search results

Summary of Contents for HPE Synergy 12000 Frame

Reviews:

Brands by name

Popular brands