HP HPE Alletra 6010 Hardware Manual Download Page 45

Page: 45 / 117

Slot 6

Slot 1

Slot 2

Serial port

OCP expansion slot

Slot 3

Slot 4

Eth0 ports, onboard

5 Slot 5

Array rear view - HPE Alletra 6010

In this example, quad fc ports are installed in Slot 1 and quad eth ports are installed in Slot 2 and Slot 3.

Serial port

Slot 1

Slot 2

OCP expansion slot

Eth0 ports, onboard

Slot 3

Shut Down the Array Using the GUI

This action shuts down the array and any expansion shelves managed by the array.

For most hardware changes you do not need to shut down (power off) the array because the components are redundant and
hot swappable.

CAUTION: When you shut down the array, all volumes go offline.

Procedure

1. In the main menu, choose Administration > Shutdown.

2. Click Shut Down Array.

Array Components 45

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands